Clearomiser Uforce-L Tank - Voopoo

5,5ml 4ml DTL RDL 25,5mm

Special offer

Complementary products

The hunters of clouds are offered a new toy signed Voopoo with this clearomizer UForce-L the force will be with you. Its three air inlets located above the tank of 4 or 5.5 ml (depending on the pyrex installed) deliver not only a tank without leaks but also a top airflow adjustable to 360 ° for a dense and precise steam.

With its 810 drip tip, the Uforce-L clearomizer is made for a DL air draw from which you will get the best by using the PNP TW coils of Voopoo. Voopoo has thought of you by including both 0.15 ohm and 0.20 ohm models in the Uforce-L kit so you can experience the excellent flavor reproduction and extended life of these sub-ohm coils. The Uforce-L embraces the newness but doesn't forget about the standard PNP coils (sold separately) which are also compatible, offering at the same time some RDL possibilities with the 0.45 and 0.6 ohm versions for example.

More info on this steam locomotive just below!

5,5ml 4ml DTL RDL 25,5mm Top Filling

Product Description

Voopoo Uforce-L Clearomizer: May the force be with you

The manufacturer Voopoo has put the package to seduce fans of big clouds with this Uforce-L qualities so undeniable that even Yoda and Vader would agree.

First of all, beware of dizziness with this top airflow adjustable to 360 °. It was necessary at least that to cover the three air inlets located above the tank to preserve a good seal and avoid having more e-liquid on the fingers than in the clearo. While we are on the subject of the tank, the Uforce-L tank can accommodate up to 4 ml of juice with its straight pyrex and up to 5.5 ml when equipped with its pyrex bulb. Filling is done simply from the top by unscrewing the top cap.

On this clearo Uforce-L, Voopoo has developed a hollow structure in the center of the tank to absorb the noise of whistling during aspiration. You will be able to vape discreetly from an auditory point of view only, because this tank designed for the DL will swing impressive clouds.

Another small innovation from Voopoo, the presence of a "heat sink" (heat sink) just above the pin 510 to avoid overheating at the base of your clearo and thus optimize the comfort and quality of your vape sessions.

The 810 drip tip at the top of the UForce-L is replaceable if you want to add your own personal touch.

The squad Pnp Coil of Voopoo to the report

The pNP coils voopoo coils are compatible with the UForce-L, however, given the DL or RDL architecture of this clearomizer we advise you not to exceed 0.6 ohm. The following models will fit very well with the UForce-L clearomizer:

- PnP VM6 0.15 ohm mesh : DL draw - use between 60 and 80 watts - ratio 30PG/70VG to 20PG/80VG - do not exceed 6 mg/ml of nicotine.

- PnP VM5 0.20 ohm mesh : DL draw - to use between 40 and 60 watts - ratio 30PG/70VG to 20PG/80VG - do not exceed 6 mg/ml of nicotine.

- PnP VM1 0.30 ohm mesh: DL draw - use between 32 and 40 watts - ratio 30PG/70VG to 20PG/80VG - do not exceed 6 mg/ml of nicotine.

- PnP VM3 0.45 ohm mesh: RDL draw - to be used between 25 and 35 watts - ratio 50PG/50VG to 30PG/70VG - do not exceed 6 mg/ml of nicotine.

- PnP VM4 0.60 ohm mesh: RDL draw - use between 20 and 28 watts - ratio 50PG/50VG to 30PG/70VG - do not exceed 12 mg/ml of nicotine.

- PnP M2 0.60 ohm mesh: RDL draw - use between 20 and 28 watts - ratio 50PG/50VG to 30PG/70VG - do not exceed 12 mg/ml of nicotine.

- PnP TM1 0.60 ohm mesh: RDL draw - use between 20 and 25 watts - ratio 50PG/50VG to 40PG/60VG - do not exceed 12 mg/ml of nicotine.

But the party doesn't end there, acquiring the UForce-L gives you the chance to test the pNP TW coils of Voopoo. These coils with Dual in One technology offer a 25% longer life and improved flavor reproduction. With your Uforce-L tank, you will receive the 0.15 and 0.20 ohm versions. The different PNP TW coils are as follows:

- TW15 0.15 ohm mesh: Very airy DL draw - use between 55 and 70 watts - ratio 40PG/60VG to 20PG/80VG - do not exceed 6 mg/ml of nicotine.

- TW20 0.20 ohm mesh: DL air draw - to use between 40 and 55 watts - ratio 50PG/50VG to 20PG/80VG - do not exceed 6 mg/ml of nicotine.

- TW30 0.30 ohm mesh: RDL air restrictive draw - to be used between 28 and 35 watts - ratio 50PG/50VG to 30PG/70VG - do not exceed 6 mg/ml of nicotine.

The coils are easily inserted into the Uforce-L by unscrewing its base and simply clipping the coil into the dedicated space.