Pod Drag X Pro - Voopoo

(1)

The Drag X pro from Voopoo, the top of the performance and autonomy !

You know the famous Drag X of Voopoo? Discover its pro version with the Drag X pro. This one is even more powerful thanks to its chipset Gene Fan 3.0 and its functionality with a 18650 or 21700 battery (not included). But also, its 100W of power.

The Voopoo Drag X pro pod, performance at its best!

The Drag X pro is even more powerful than its predecessor! And for good reason, it hides a Gene Fan 3.0 chipset, the most advanced chip of the brand. Indeed, this one is 20% more powerful than the previous chipsets and is very reactive, in 0.001 seconds. Here too, the safety features are in order with protection in case of short circuit, overheating, overload, output overcurrent, excessive discharge, polarity inversion and puffs of more than 8 seconds.

You can not only use an 18650 battery, but also a 21700 battery instead Please note that the battery is not included in the delivery. The battery door is located on the bottom of the pod. The charging is done quickly with the included USB-C cable (5V/2.5A). However, we strongly recommend to use a external battery charger to preserve the life of the battery. To you the long sessions of vapotage!

And in terms of power, the ecigarette can go up to 100W (against 80W with the Drag X). You find the following modes:

- Smart: the pod will detect the value of the resistance installed to adapt the power (from 5 to 100W)

- RBA

- TC: temperature setting after installation of the module found on the Voopoo website

The settings are done from the0.96 TFT screen

Another innovation of the Drag X pro is the on/off lock button to turn the mod off and on. However, you can still press the switch 5 times to turn on your pod. Be careful, when you receive your pod, it is configured in lock mode by default. To unlock it, press the fire button (switch) 5 times

When the charge level of your battery is low, you will not lose power thanks to a boost system that increases the output voltage to 8.5V. The key? More stable flavors even if your vape has little battery.

The Drag X pro Voopoo: A versatility of draw

The new TPP-X cartridge of 5.5 ml PCTG is compatible with TPP and PNP resistors from Voopoo for a versatility of draw: DL, RDL and MTL.

2 resistors are delivered for a DL overhead draw:

- TPP DM2 resistor of 0.20 ohm (mesh): DL overhead draw - to be used between 40 to 60W - ratio 50PG/50VG to 20PG/80VG

- TPP DM3 0.15 ohm (mesh) resistor: DL overhead draw - to be used between 80 and 100W - ratio 50PG/50VG to 20PG/80VG

The mesh technology promotes both the flavors and the production of steam. For even more sensations, modulate theairflow adjustable to 360 ° for a more or less air

An easy use for the electronic cigarette Voopoo Drag X pro

Either you vape by pressing the switch button, or directly by sucking.

To fill the TPP-X cartridge, you do not need to remove the tank. It is done from the side. To do this, press the black button on the top cap and turn to the left. Then remove the silicone cap to fill. And finally, close the silicone cap and turn to the right.

However, to change the resistor you will need to remove the cartridge. Then pull the coil, prime a new one and place it. And finally replace the cartridge, fill and wait 10 minutes before vaping.

The elegant design of the ecigarette Drag X pro Voopoo

The Drag X pro is made of zinc alloy and leather. The zinc alloy allows a great strength. While the leather provides comfort with its soft touch as well as a touch of elegance. The ergonomic curves of the pod promote anexcellent grip.

The Voopoo Drag X pro pod comes with:

- 1 Drag X pro mod

- 1 x 5.5ml TPP-X cartridge

- 1 TPP DM2 resistor of 0.20 ohm

- 1 TPP DM3 resistor of 0.15 ohm

- 1 USB-C cable

- 1 user manual

The characteristics of the kit Drag X pro Voopoo :

- Dimensions: 135.5 mm x 34.5 mm x 28.8 mm