- New versions
Gen Air 40 Cartridges - Vaporesso | Pack x2
Vaporesso Gen Air 40 cartridges compatible with the Gen Air 40 pod. The Gen Air 40 replacement cartridge will make your life easier, because you can change your e-liquid in a flash! Also, it comes as a replacement for a worn out tank.
The adjustable airflow that is to say the system of airflow AOP (Adjustable Airflow On Pod) comes in the form of a push button for precise adjustment. Thus, you can switch from a tight draw MTL to a more airy draw RDL. It's up to you to experiment with different vape experiences! The flavours will be at the rendezvous and the loss of air at the entrance is reduced. But also, the tank is equipped with SSS anti-leak technology.
This 4.5 ml magnetic PCTG cartridge offers you an MTL or RDL draw. The filling is done on the side.
The cartridge is compatible with GTX coils (sold separately).
Sold in packs of 2 without coils.
Gen Air 40 replacement cartridges from Vaporesso
The pack of 2 cartridges Gen Air 40 allows switching more easily and quickly e-liquid to vary the pleasures. But also, this tank will replace a worn cartridge.
With what equipment to use the replacement cartridge Gen Air 40?
The Vaporesso Gen Air 40 cartridge is compatible with the pod Gen Air 40.
What are the characteristics of the cartridge Vaporesso Gen Air 40?
The adjustable airflow of the magnetic cartridge in PCTG that is to say the airflow system AOP (Adjustable Airflow On Pod) is in the form of a push button for precise adjustment. Thus, you can switch from a tight draw MTL to a more airy draw RDL. It's up to you to enjoy a variety of vape experiences! The flavours will be at the rendezvous and the loss of air at the entrance is reduced. But also, the tank is equipped with SSS anti-leak technology.
The cartridge is compatible with the GTX coils greater than or equal to 0.3 ohm (sold separately) :
- 0.3 ohm GTX coil (mesh): air draw DL - to be used between 32 and 45W - ratio 50PG/50VG to 20PG/80VG - compatible with low nicotine levels (from 0 to 6 mg/ml)
- 0.4 ohm GTX coil (mesh): RDL draw - to be used between 26 and 32W - ratio 50PG/50VG or 30PG/70VG or 40PG/60VG
- GTX 0.6 ohm coil (mesh): RDL draw (balance between flavours and steam) - to use between 20 and 30W - ratio 50PG/50VG or 30PG/70VG or 40PG/60VG - compatible nicotine rate from 0 to 9 mg/ml
- GTX 0.8 ohm coil (mesh): RDL draw - to be used between 12 and 20W - ratio 50PG/50VG - compatible nicotine rate from 0 to 18 mg/ml
- GTX 1.2 ohm coil (mesh): MTL tight draw (promotes both flavour and vapor production) - use between 7 and 11W - ratio 50PG/50VG to 80PG/20VG - compatible with nicotine salts, CBD and high nicotine levels (from 0 to 18 mg/ml)
- GTX 1.2 ohm coil (regular): MTL tight draw - use between 8 and 12W - ratio 50PG/50VG to 80PG/20PG - compatible with nicotine salts, CBD and high nicotine levels (from 0 to 18 mg/ml)
How to use the Gen Air 40 cartridge?
The Gen Air 40 Vaporesso cartridge of 4.5 ml is easily filled on the side. To do this, remove the cartridge from the battery, then the red silicone cap. To change the coil, first remove the cartridge from the pod and then the damaged coil. Prime a new coil and insert it before filling the tank, repositioning the cartridge and waiting a few minutes to vape. To change the magnetic cartridge, you just have to unclip the tank and clip another.
Attention, it is necessary to change your resistance about every 2 weeks depending on your use. Remember to replace your coil when you change flavour or if you feel a burnt taste.
- Capacity (ml)
- 4,5ml
- Type of inhalation
- MTL, RDL
- Fill type
- Side Filling
- Packaging
- Pack of 2 units
- Compatible coils
- GTX V2 coils
- Country of manufacture
- made in China
Complementary products
Kit pod Gen Air 40 - Vaporesso Kit pod Gen Air 40 - Vaporesso
- Special offer
Forbidden under 18 years old